Jr Marine Bravo 3 Cutout Template

Jr Marine Bravo 3 Cutout Template - If you can only do one mod, the jr marine kit is best, but having 3 access holes is awesome. You could even figure out the percentage of difference between the pic and actuall drive and print out the template in the top pic to the correct size. I am being told that my gimbal ring needs replaced for my bravo 3 outdrive. With the kit comes a cardboard template that shows you where to cut on the gimbal housing. Changing the gimbal ring or steering lever without removing the engine is very easy on my boat. Cut through all green holes first and red holes last.

1 the standard tap and drill on both sides of my transom plate, or 2 the jr marine method of drilling and cuting a plate size hole in the back or the transom plate (both options are expensive). Do not slip and cut outside of window pattern!! Changing the gimbal ring or steering lever without removing the engine is very easy on my boat. Cut drill template out on solid black line as close as possible place pattern on gimbal, lining bottom edge of pattern with bottom flat edge of gimbal housing, centerng template from right to left and scotch tape pattern to housng. Wait to get the actual template to drill the screw holes though.

Diesel Drives Bravo One X® Diesel / Bravo One XR Diesel Mercury Marine

Diesel Drives Bravo One X® Diesel / Bravo One XR Diesel Mercury Marine

cutout marine by 40Kun on DeviantArt

cutout marine by 40Kun on DeviantArt

2501 JR Marine Bravo Swivel Shaft Cover Plate Primeau's Marine and

2501 JR Marine Bravo Swivel Shaft Cover Plate Primeau's Marine and

Mercury Bravo Three XR® Hi Tech Marine

Mercury Bravo Three XR® Hi Tech Marine

23 JR marine Barry Bowe

23 JR marine Barry Bowe

Jr Marine Bravo 3 Cutout Template - Do the math to figure where to make the cut out. If you can only do one mod, the jr marine kit is best, but having 3 access holes is awesome. Changing the gimbal ring or steering lever without removing the engine is very easy on my boat. I am being told that my gimbal ring needs replaced for my bravo 3 outdrive. With the kit comes a cardboard template that shows you where to cut on the gimbal housing. I have found two options:

Cut through all green holes first and red holes last. Do the math to figure where to make the cut out. My boat has the merc threaded plug kit and a jr marine cover plate modification. Do not remove this pattern until all holes are. I am being told that my gimbal ring needs replaced for my bravo 3 outdrive.

Cut Through All Green Holes First And Red Holes Last.

If you can only do one mod, the jr marine kit is best, but having 3 access holes is awesome. 1 the standard tap and drill on both sides of my transom plate, or 2 the jr marine method of drilling and cuting a plate size hole in the back or the transom plate (both options are expensive). Do the math to figure where to make the cut out. I have found two options:

Do Not Slip And Cut Outside Of Window Pattern!!

Changing the gimbal ring or steering lever without removing the engine is very easy on my boat. You could even figure out the percentage of difference between the pic and actuall drive and print out the template in the top pic to the correct size. This kit will only work on bravo 1, bravo 2, bravo 3, and alpha 1 gen 2. Carefully cut out window pattern with die grinder cutting through all of the 3/32 holes.

I Am Being Told That My Gimbal Ring Needs Replaced For My Bravo 3 Outdrive.

My boat has the merc threaded plug kit and a jr marine cover plate modification. Cut drill template out on solid black line as close as possible place pattern on gimbal, lining bottom edge of pattern with bottom flat edge of gimbal housing, centerng template from right to left and scotch tape pattern to housng. Wait to get the actual template to drill the screw holes though. This is where the jr marine repair kit comes into play.

Do Not Remove This Pattern Until All Holes Are.

With the kit comes a cardboard template that shows you where to cut on the gimbal housing.